Ceramic Lined Hydrocyclones

Ceramic Hydrocyclones / Ceramic Lining Hydrocyclones / Wear Resistance Ceramic Lined Hydrocyclones

GTEK Ceramic Lined Hydrocyclones

INTRODUCTION

SPECIFICATION

Description

Hydrocyclone is a continuously device that utilizes centrifugal force to accelerate the settling rate of particles. During operation, the slurry feed enters the cyclone under pressure through the feed pipe into the top of the cylindrical feed chamber. As the feed enters the chamber, as result of the high centrifugal forces, the particles migrate downward in a spiral pattern through the cylindrical section and into the conical section. At this point the finer particles migrate toward the center and spiral upward and out through the vortex finder, discharging through the overflow pipe. The coarse particles remain in a downward spiral path along the walls of the conical section and gradually exit through the apex orifice.

Application

GTEK ceramic hydrocyclones are specifically designed for highly abrasive processes where the chemistry is not suitable for rubber liners. GTEK ceramic hydrocyclone can be used for classification in mineral processing and has proven to be a very economical means of classification, especially in closed circuit grinding operation. GTEK ceramic hydrocyclones can be applied to dewatering and desliming mineral sands, bauxite ore, phosphate rock, concrete sands, and coal washery fines in mineral processing circuit.

Features & Benefits

1. Wear resistance liner manufactured from high alumina oxide or reaction boned silicon carbide for some models
2. Delivery maximum efficiency, maximum capacity due to scrolled evolute inlet design
3. Lower cyclone operating costs, longer wear Life
4. Maximum separation efficiency, maximum hydraulic capacity
5. Easier installation and maintenance
6. Reaction bonded silicon carbide ceramic available for lower cones and spigots

ceramic lined hydrocyclone
ceramic lined hydrocyclone cluster
ceramic lined hydrocyclone cluster
Specification of Ceramic Lined Hydrocyclones
Model Interior
Diameter
(mm)
Cone
Angle
(°)
Overflow
Diameter
(mm)
Feed
Size
(mm)
Inlet
Pressure
(Mpa)
Process
Capacity
(m³/hr)
Range
(um)
Dimensions
(LxWxH)(mm)
FX660-GT 660 20 180-240 16 0.03-0.2 250-350 74-220 1250 890 2650
FX500-GT 500 20 130-200 10 0.03-0.3 140-220 74-200 850 790 2050
15 74-150 850 790 2380
FX350-GT 350 20 80-120 6 0.04-0.3 60-100 50-150 775 605 1765
15 50-120 775 605 2115
FX300-GT 300 20 65-115 5 0.04-0.3 45-85 50-150 665 585 1310
15 40-100 665 585 1505
FX250-GT 250 20 60-100 3 0.06-0.35 40-60 40-100 540 480 1180
15 40-100 540 480 1220
10 30-100 540 480 1380
FX200-GT 200 20 40-65 2 0.06-0.35 25-40 40-100 435
360 1050
15 30-100 435 360 1115
10 30-100 435 360 1205
FX150-GT 150 20 30-45 1.5 0.06-0.35 11-20 30-74 280 295 690
15 30-74 280 295 900
8 30-74 280 295 1270
FX125-GT 125 17 25-40 1 0.06-0.35 8-15 20-100 210 185 620
8 20-74 250 240 985
FX100-GT 100 20 20-40 1 0.06-0.35 5-12 20-100 260 210 525
15 20-100 268 215 720
8 20-100 268 215 1000
FX75-GT 75 15 15-22 0.6 0.1-0.4 2-5 20-74 240 230 465
6 5-40 240 230 800
FX50-GT 50 15 11-16 0.3 0.1-0.4 1-2 10-74 160 155 350
6 5-30 160 155 590
Copyright © 2016 GTEK MINERAL TECHNOLOGIES CO.,LIMITED. All rights reserved.